Fishing Wire Ranger Boats
TUESDAY, OCTOBER 13, 2020

CONTESTS
Participating anglers must catch a largemouth bass, smallmouth bass, channel catfish, and bluegill before October 31 to be entered into sweepstakes for prizes and more.
The 8th Annual Fly Tying Competition brings an exciting new addition: online submission and two rounds of online judging.
FISHERIES
Watershed restoration jobs on the Oregon Coast got a big boost this summer and fall as the NOAA Restoration Center awarded Wild Salmon Center (WSC) $824,000 to support habitat restoration projects implemented through the Coast Coho Partnership (CCP).

Here's a useful update from Joe DuPont, Regional Fisheries Manager for Idaho Fish and Game, on the current status of the steelhead run in the Clearwater River.
The Army Corps of Engineers will open a public comment period on a permit application for a fish farming pilot project off Florida’s southwest coast, following demands from critics and a newly issued pollution permit.
FISHING SPOTS
Brandon Pellham's 26.5" brown is just the latest whopper caught in this productive tailwater fishery.

FISHING TIPS
They can be a challenge, but knowledgeable persistent anglers can connect with Vermont's landlocked salmon as October chills the waters.
Here are a series of videos from Sunline that provide some of the best visual instruction in knot-tying we've seen anywhere.
Fly fishers are reminded by Colorado Parks and Wildlife that line handling on the water can be as important as casting skills when it comes to stream fishing for trout.

GEAR
The Department of the Interior has announced that it finalized electric bike (or e-bike) regulations that pave the way for land managers to allow more people, especially older Americans and those with physical limitations, to experience bicycling on public lands managed by the National Park Service, the Bureau of Land Management, U.S. Fish and Wildlife Service and the Bureau of Reclamation.
ICE FISHING
With the introduction of the new MEGA 360 Imaging Ice Adapter, Humminbird brings that exclusive technology to ice fishermen.
INDUSTRY
Here's an interesting take from David Guest, writing for Fishing Tackle Retailer, on Columbia as a possible alternative source for outdoors goods now made in the Far East.
ORGANIZATIONS
The best in Florida outdoor writing, photography, and videography was honored Sept. 30 by the Florida Outdoor Writers Association (FOWA) during an online broadcast.
The American Fly Fishing Trade Association has hired Whitney Tilt as the first-ever Executive Director for the AFFTA Fisheries Fund.
SCHOLARSHIPS
Four writers from Florida colleges and universities have been awarded $1,000 each as the 2020 recipients of the Florida Outdoor Writers Association scholarship for outdoor communicators.
STATES
A new access road now provides a riverside turn around to facilitate shore angling and launch of canoes and kayaks.
The calendar is a one-stop shop for figuring out when and where to go hunting and fishing in West Virginia and includes a lot of interesting facts about our state's wildlife as well as great art work.
The MRAP program provides incentive payments and habitat improvement help to private landowners who open their properties to the public for walk-in hunting, fishing, or wildlife viewing.
Agents recovered the body of Darryl J. Batiste, 65, of Lacombe, around 6:15 p.m. from Bayou Des Mats off Lake Pontchartrain on the Big Branch National Wildlife Refuge.
The Alaska Department of Fish and Game (ADF&G), Division of Sport Fish will be using a fish pesticide called rotenone during the week of October 12, 2020, in Kings and Anderson lakes to remove invasive northern pike.
New rules include new walleye and catfish daily limits as well as changes to aquaculture production.
The Mud Creek Public Boat Ramp located on Lake Guntersville near Hollywood, Alabama, will temporarily close for repairs beginning October 18, 2020.
TOURNAMENTS
Coley McGowan, 25, a Gadsden, Alabama native, took home the crown with 181 total inches of catch and release largemouth bass for the two-day event.
Brandon Palaniuk had a giant final catch to win the Bassmaster Elite event at Santee Cooper Lakes, S.C. with a 4-day total of 72 pounds 2 ounces.
WILDLIFE
A new state record 18-foot, 9-inch, 104 pound python was captured by a pair of intrepid hunters in the swamps of south Florida.

Here are some interesting tips on jackplates for bass and flats boats, from noted tournament pro and flats angler Bernie Schultz.

By Bernie Schultz

Ask any touring pro if a hydraulic jackplate is worth the money, and I’d bet their answer would be an emphatic “yes!” On the Bassmaster Elite Series, they’re considered essential equipment … for multiple reasons.

Although they may be a bit pricey, hydraulic jackplates can vastly improve the performance of your bass boat or flats boat    — both at the top end and in the ability to run shallower at low or high speeds. They can even improve the ride.

A simple touch of a lever or toggle switch allows the operator to raise or lower the outboard engine while under power, at any speed. Combine that with the engine’s power trim and you’ll realize advantages beyond the obvious.

Skinny as she goes

Consider bedding season when, on some lakes and rivers, you’re dealing with vast, shallow flats — places where the fish may concentrate only in small areas.

Covering water is required to find those fish, and using a trolling motor to do it can be tedious and time consuming. Idling with the main engine makes much more sense. But without a jackplate, you would have to trim the engine up, which squats the stern and bogs the engine down, making maneuvering much more difficult … not to mention the added disturbance it causes in situations requiring stealth.

With a hydraulic jackplate, you can raise the engine up high and adjust the trim to give the boat a flatter attitude. This not only improves maneuverability, it allows you to increase idle speed to cover more water while creating less disturbance.

Hydraulic Jackplates can improve your boat's performance in multiple ways.

The ability to raise the engine also allows you to plane off in shallow water — much shallower than would be possible with a fixed engine height. This is a huge advantage, especially in places that normally require long idle times to reach adequate planing depths.

A trick I learned from flats fishing in saltwater is to take advantage of the clockwise rotational lift of a spinning prop. By turning the steering wheel all the way to the left (which puts the leading edge of the skeg facing right, the same direction of the prop’s clockwise rotation) you then realize added lift when applying full throttle. This kicks the stern around and actually throws out a small wake, which provides a slight increase in water depth for the prop to bite in. In addition, with the engine cocked at an angle, you minimize contact with lake bottom as the boat leans to one side. As the hull begins to plane, you gradually lower the engine to submerge the water pickup. (This is critical, as you do not want to starve the engine for water for any length of time.)

Using this counterclockwise maneuver, the boat will usually spin to a full circle before reaching planing speed. And it happens quick, so it’s a good idea to plan your exit route ahead of time. Once up and running, you simply adjust the trim and engine height to your liking.

Here’s a short video that demonstrates the technique.

Here's an aerial view of a boat performing a circular, shallow-water hole shot. Notice the mud trail.

 

Digging deeper

While hydraulic jackplates prove beneficial in the shallows, they can also enhance performance in deep water.

Because they set the engine farther from the transom (usually up to 12 inches), it effectively increases the overall length of the boat — which, in turn, makes it bridge more water. And that’s good, especially in rougher conditions. But the biggest advantage is the additional leverage they provide.

By dropping the jackplate and tucking the engine under, you can greatly improve handling in choppy water. This added “pinch” on the hull and motor will force the bow down to create a flatter ride. If you have ever plowed through rough seas in a strong headwind, then you know how critical this can be. 

Bass boats are notoriously stern heavy. When you factor the weight of multiple batteries, an onboard charger, fuel, livewells, Power-Poles and gear, keeping the bow down can become a serious challenge, and a hydraulic jackplate will compensate for that. 

Need for speed

For the totally performance minded, jackplates also add top-end speed with better handling. By lifting most of the lower unit out of the water, you minimize torque at the wheel and decrease drag. Add a bit of trim and the bow will lift while increasing speed. The trick here is finding just the right height with the plate and proper trim to reach the ideal RPMs … all while maintaining sufficient water pressure.

Every boat will be different, so it may take some tweaking with the right prop and engine position to realize your boat’s top-end speed.

There are a number of quality jackplates on the market, including CMC, SeaStar, Bob’s Machine Shop and T-H Marine. And most of these brands offer multiple offset sizes (6, 8, 10 and 12 inches are common) capable of handling the weight of large-block outboards. 

I run a 12-inch Atlas by T-H Marine. It’s quick, quiet and self-contained with no messy remote pumps or hoses, and it works well under power in a chop. I also run one on my saltwater skiff and have for years with zero issues. 

Most brands offer a console gauge to monitor engine height, but they won’t tell you if your water pickup is submerged and functioning. For that you’ll need a reliable water pressure gauge. Believe me; you can jack an engine to the point where it’s starving for water. If you do that for more than a few seconds at speed, you can fry your engine.

One last tip: If you’re using your jackplate for top end performance, I highly recommend mounting a lever-style switch on the steering column. Just like the blinker switch in your car, it’s quick and handy. In fact, I suggest mounting a matching trim lever on the opposite side. That way, both hands are always on the wheel, which will ensure a much safer boating experience. 

Follow Bernie Schultz on Facebook and through his website

Click here to unsubscribe

This newsletter was sent to [Email]
Fishing Wire - 2271 N Upton St., Arlington, VA 22207
Copyright © 2020, Outdoor Wire Digital Network.
All Rights Reserved.